Top 10 typical forklift mishaps ， forklift operation ought to focus on these matters ！.

Don't take too lightly the forklift at work. If the operation is bad, there will certainly be significant accidents in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that hinder the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the driver needs to first validate that the load is steady and reputable.
4. The beginning needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with tons unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the range in between the two forks need to be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift needs to be stopped with the brake. .
4. The speed of the lorry must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it must be noted that the fork idea should not touch various other goods or items. The lots should be supported with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the emergency brake button.
3. The engine is turned off and the power is removed. (Except for special scenarios, such as the vehicle driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water ought to be added.
2. Check the safety and security efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do Stand-on Electric Pallet Stacker not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they come across large or heavy items and go to the vehicle driver's line of vision, they need Electric Forklift Truck for Warehouse to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844